Top 10 Best Biscuit Joiners in 2019

Best Biscuit Joiners

Whenever woodwork requires a simple, quick and sufficiently strong method for light and medium type of woodwork applications, one can easily make good use of a Biscuit Joiner.  It is ideal for use for drawers, boxes, cabinet carcasses, miters, face frames, edge banding, etc. It also serves as a good substitute which is lightweight for mortise and tenon joinery.Biscuit Joiners are the quickest and the simplest for woodworking joints. All that is required to do is to mill the slots in the mating pieces and then use glue.  This is followed by slipping the biscuits in place and then assembling and clamping.  The whole process usually does not take more than a minute and the joint ends up in perfect alignment.  It is also sufficiently strong for a variety of applications. Moreover, it is important to note that it provides a horizontal wiggle room in the joint which makes it convenient and simple to tune for adjusting at the assembly line. Many other forms of joinery would not offer this kind of facilitation.

Best Practices for Best Biscuit Joiners

It is extremely important to firstly check for the depth of the cut. Prior to use the Biscuit Joiner, it is tuned up first so that it would operate properly for the project at hand. Once the Biscuit Joiner has been properly adjusted and tuned, it would be able to cut a slot 1/32″ deeper than half the width of the biscuit.  This additional 1/32″ is what is the wiggle room provided by the biscuit joiner. Moreover, it can be used for the glue as well. In case, this is made deeper than that, the biscuits would end up getting fat too much-embedded o one piece.  This would reduce the holding power required by the user. On the other hand, if the wiggle room is too shallow, the biscuits would not be able to fit.

A slot can be milled in a piece of scrap wood to test this. Once milled, the biscuit can be inserted into the slot. It is normally very gently tapped in until it bottoms out. One can then employ a sharp pencil to draw a line on the biscuit at the place where it touches the scrap board.  After this, the biscuit can be removed and the opposite edge inserted into the slot and another line can be drawn. At this point, the first line drawn by the user should be hidden inside the biscuit slot. In case, this does not occur, an adjustment for a deeper cut would be required. The distance between the lines is then measured after removing the biscuit. In case, it is close to 1/16″, the user can simply start to mill biscuit slots. In case, it is not, the user would have to consult the concerned user manual to readjust the depth of the cut. Moreover, the user needs to ensure that the fence of the user is square to the face of the machine when fixed at90-degrees. This is important as if this is not the case, there would be chances of sloppiness occurring in the biscuit slot.

The Process of Gluing

A sufficient amount of glue would also need to be ensured in the joint for the simple reason that biscuits absorb the glue.  This leads to the swelling of the biscuits and this causes precise alignment and the holding power is enhanced. In case, the user is unable to fulfill this condition, he/she might end up getting a joint which might fail and would have a poor alignment. Users can employ a variety of techniques to get the sufficient amount of glue into the joint. Once can simply squeeze the glue in after placing the tip of the glue bottle over the slot. Moreover, a special glue bottle might be employed which would easily fit into the glue slot to avoid any possibility of creating a mess. This would deliver just the right amount of glue into the slot. As an alternative, a flux brush can be used to spread the glue evenly in the slot and coats its walls as well. Similarly, glue can be applied to sides of the biscuit as well to ensure proper coverage. It is important to ensure that neither too much nor to little glue is used. However, having just a bit more than what is required ensures that the joint would be solid. Users are better off with using a type of glue that provides more open time for biscuit assembly. This is important for the complex type of assemblies. It is better to be wipingoff a little extra glue than to have an insufficient amount of glue which increases the likelihood of the failure of the joint.

Right Size of the Best Biscuit Joiners

It is the best to use the largest possible biscuit for a given application. Normally, users work with #20 (1″ x 2-3/8″) and on other occasions might when narrower or thinner materials are involved, the choice would fall on #0 (5/8″ x 1-3/4″) or #10 (3/4″ x 2-1/8″). In case, the joints are extraordinarily small as is the case with face frames, picture frames, or small boxes, etc. FF (FaceFrame) biscuits (1/2″ x 1-11/64″) can be used. For the latter, however, a blade change is essentially required as FF biscuits are rounder. The use of the #20 biscuit, on the other hand, might require the user to trim off a part of the biscuit that protrudes out of the joint. Other applications might require a fence. Some users instead might use the base of the Biscuit Joiner as a reference surface as they complain of slight rocking when using the fence which might throw off the positioning of their joint. If the fence is used, one must ensure its full-fledged engagement to the workpiece.

The Joining of Miters

The use of Biscuit Joiners is a very simple way to align and strengthen miter joints. If other methods are tried, it might end up as quite a challenge and could cause a lot of frustration. However, different Biscuit Joiners have different levels of capabilities in this particular type of application. Many of the Biscuit Joiners are able to provide a fence which pivots from 0 to 90-degrees, However, there are others might tilt forward past the 90 degrees. They might even go all the way up to 135 degrees. (we have written extensively for the best generators brands)

The user needs to be careful in all these cases and ensure that the biscuit’s positioning on the slot on the miter is such that the cutter would not be able to cut all the way to the outside face of the piece. In case, the 90 degrees max Biscuit Joiners are used, the fence is set to 45 degrees. The reference, in this case, is the shorter or inside surface of the mitered piece.For Biscuit Joiners that pivot to 135 degrees, milling slots is a lot easier. The fence is simply set to 135 degrees and it is placed on the longer surface on the outside of the mitered piece. The tool can be easily positioned in this type of setup. However, it is still a good practice to make sure that the fence is flush against the workpiece.  Moreover, it must be ensured that prior to plunging, the face of the biscuit joiner is properly held against the mitered surface.

Top 10 Best Biscuit Joiners in 2019

Picture
Name
Feature
Price
Rating
Picture
Name
Feature
Price
Rating
1.574447 XL DF 700 Domino Joiner Set from Festool
It occupies a very small floor space on the job site or workshop.
$$
4.9
2.574432 Domino Joiner DF 500 Q Set from Festool
Its tenon is stronger than dowels or biscuits.
$$
4.8
3.Classic x 101600 Biscuit Joiner from Lamello
It stays accurate for literally decades.
$$
4.7
4. DEWALT DW682K 6.5 Amp Plate Joiner  
It stays accurate for literally decades.
$$
4.6
5.PJ7000 Plate Joiner from Makita
It is highly accurate.
$$
4.6
6.XJP03Z 18V LXT Lithium-Ion Cordless Plate Joiner from Makita
The Biscuit Joiner can be used anywhere.
$$
4.6
7.557 7 Amp Plate Joiner Kit from PORTER-CABLE
The Biscuit Joiner is very powerful at 10,000 RPM>
$$
4.5
8.5 Amp Wood Biscuit Plate Joiner from VonHaus
The tool is very powerful.
$$
4.5
9.TruePower Biscuit Plate Joiner from Gino
The tool is extremely powerful.
$$
4.5
10.4″ Plate Joiner from Chicago ElectricPower Tools
It is able to make deep cuts.
$$
4.5

 

1. 574447 XL DF 700 Domino Joiner Set from Festool

The 574447 XL DF 700 Domino Joiner Set from Festool is a part of the Domino Joiner revolution and has in fact made this revolutionary concept even larger.  Prior to its use, machines like the hollow chisel mortises as well as other slot mortises used to occupy a lot of floor space in the workshop. These were also extremely expensive to purchase and were demanding of a lot of efforts as far as their installation was concerned. Moreover, this was also compounded by the maintenance requirements and the need to bring the materials to the tool. This equipment has provided the answer in the form of an extremely elegant solution for performing large-scale joinery in an efficient way.

General Features

The 574447 XL DF 700 Domino Joiner Set from Festool is extremely easy to use and it is also an amazingly fast and accurate machine. The Domino XL is complementary to the capabilities of the earlier introduced original machine known as original Domino DF 500. The maximum tenon size of this newer machine is 5 1/2 inches in length.  The machine is capable enough to carry out big tasks as well.  Its tenons are longer and thicker and massive slabs, gates, and doors, etc. can be joined very precisely and quickly. Similarly, it is also possible to construct highly durable beds and tables, etc. The entire machine is so nimble and lights that it can literally be employed at all possible locations on the jobsite or in the workshop. In case, the workpiece might prove to be too massive to be transported to the machine, the machine can move to the workpiece.  Solid hardwood tenons can be precisely placed and this guarantees that a perfect fit is possible. Moreover, the finished product is so robust and precise that it hasthe capacity to last past many generations. The set version of the machine includes cross top and trim accessories. The package contains a Plug-it Power Cord, D12 cutter, Wrench, support Bracket, Trim Stop and Cross Stop, and a T Loc Systainer Sys 5 besides the main equipment Domino XL 700. The machine’s Product Dimensions are 16.5 x 11.5 x 11.5 inches and it weighs only 22.1 pounds.

Pros

  • The 574447 XL DF 700 Domino Joiner Set from Festool is extremely light.
  • It occupies a very small floor space on the job site or workshop.
  • It can be taken to the workpiece if it is too massive.

Cons

  • It is not light enough to replace hand-held tools.

2. 574432 Domino Joiner DF 500 Q Set from Festool

The 574432 Domino Joiner DF 500 Q Set from Festool system comprises of a Domino Joiner along with Beech and Sipo Domino tenons which have been pre-fabricated. A revolutionary cutting method is employed by the Domino Joiner.  It has got very simple features for indexing and the mortise size can be adjusted very easily as well.  It is able to make mortises without any flaws every time it is required.

General Features

The Domino tenon is 100% rotation-proof and for this reason, it is highly impressive as well. It is also extremely strong as compared to dowels or biscuits. It has got a large gluing surface which provides an adequate amount of area which allows the joints to get the added strength that makes all the difference. The cutting mechanism which is both unique as well as patented makes very good use of a spiral cutter which has got a carbide tip. This tip oscillates while rotating with the aim of creating a perfect type of mortises every time it operates. This particular action is thus able to create a very clean entry and a perfectly flush surface is enabled.  At the same time, the possible heat build-up in the tooling is prevented so that the cutter can have a very long life.  The DominoJoiner is thus extremely easy to employ. All types of adjustments related to height, depth or angle can be accomplished by the use of scales with positive stops for accurate indexing and repeated work. The package contains stop pins which are used for the consistent type of indexing against the workpiece edge.  This is extremely important in terms of perfect alignment in the case of the panels being joined together.Adjustable fence ranges from 0 to 90º with positive stops at 22.5, 45, 67.5, and 90º. The product dimensions are 15.5 x 11.5 x 6.4 inches and its weight is 6.61 lbs.

Pros

  • The Domino Joiner has got a unique cutting mechanism which is patented.
  • Its tenon is stronger than dowels or biscuits.
  • The product is extremely light in weight.

Cons

  • It comes with a single cutter of 5 mm. Others of different sizes need to be purchased.

(we have also  written a comprehesive guide about the finish and brad nailers ).

3.Classic x 101600 Biscuit Joiner from Lamello

The Classic x 101600 Biscuit Joiner from Lamello is from a manufacturer who has invented the plate joining technique.  It is considered a very high-quality biscuit joiner as it lives up very nicely to its distinguished reputation. The fence, the slideshoe, and the multi-function stop square are manufactured from a single piece of metal which is machine-milled with precision. This particular plate joiner is the only one in the world which has been manufactured on this pattern.

General Features

The Classic x 101600 Biscuit Joiner from Lamello has been produced using very high-quality construction. It is highly accurate and the accuracy can last for as long as decades. The Joints are always lined up perfectly flush and thus feature saves the user a lot of time as well as money. It has the capacity to cut grooves for 12 biscuits without the need to change the cutting tool. The swelling fence which is styled anew has got a beveled edge which allows the user to see the angle as well as measuring scales quite easily.  It also has positive stops at the most widely used cutting angles which are 22.5, 45, 67.5 and 90 degrees. The Style Multi-function stop square is very new is placed in parallel to the footplate. This is because of the precision dovetail design. For easy referencing against work surfaces, it is flush to the sides of the base. Moreover, it allows for an angle of 135 degrees.  This enables outside referencing of the 45 degree mitered joints.It is also able to slide and lock on to the bottom of the slide shoe. This allows for the vertical use of the tool extremely safe and quick at the same time.  In order to quickly remove the cassette base with a thumbscrew, a central locking system is present which enables the proper maintenance and access to the cutter.The Product Dimensions are 16.8 x 12.5 x 6 inches and the weight is 10.5 lbs.

Pros

  • It stays accurate for literally decades.
  • Without a change of cutting tool, it cuts grooves for 12 biscuits.
  • It has got a one-year limited warranty.

Cons

  • It does not come in a proper carrying case.

4. The DW682K 6.5 Amp Plate Joiner from DEWALT

The DW682K 6.5 Amp Plate Joiner from DEWALT lets its users cut slots in order to hold the biscuits with a high level of precision.  The kit comprises of a fence which is extremely easy to adjust, a heavy duty nonmarring shoe as well as common to all biscuits pre-set stops.  This allows the user to aptly craft very solid joints very accurately and very quickly as well. It has got a dual rack and pinion fence which is used to make sure that the fence and the blade stay parallel all the time. For any biscuit Joiner, it is extremely important to be highly accurate.  The DW682K 6.5 Amp Plate Joiner from DEWALT has got the one-piece fence fully integrated into the Biscuit Joiner’s overall design. this is instrumental in providing a high level of convenience and it is also adjustable.

General Features

It must be noted that the one-piece fence which is integral is adjustable and it can tilt in the range of 0 to 90 degrees.  Without removing the fence, it allows the making of flush cuts. Moreover, the 45-degree locating notch in the fence lets the user index of the mitered joint’s outside surface. The same is true for nonmarring, retractable, heavy-duty aluminum shoe, anti-slip pins, and present depth stops for all the most common biscuit sizes.  The specifications include 10,000RPM RPM speed at no load, 7/8″ arbor, 20 mm depth of cut, 0, 10, 20 biscuit sizes, a carbide blade, Torx key, a vacuum adapter, wrench as well as a kit box.The Biscuit Joiner is also equipped with a DW682K’s 6-1/2-amp, 10,000 rpm motor. Its powerful motor cuts at depths of up to 20mm and this are true for even the hardest of all types of wood. It is this powerful nature of the tool that actually makes it very safe to use. Such a power prevents any undue movements on part of the workpiece.

Pros

  • The Biscuit Joiner has got a very powerful motor.
  • It is highly accurate.
  • It has got an easily adjustable fence.

Cons

  • Dust port might clog up and require cleaning

5. PJ7000 Plate Joiner from Makita

The PJ7000 Plate Joiner from Makita has got its front body manufactured out of Aluminium and this has provided the Plate Joiner with a high level of durability. The Plate Joiner has also been equipped with a blade cover which is toothless as well as a shaft lock which allows for very quick changes of blades. The Plate Joiner is quite accurate and makes cuts using acurrent amperage of 5.6 Amps at 120 VAC.  The body of this PJ7000 Plate Joiner from Makita has been designed by the manufacturer to be as ergonomic as possible enabling the user to grip it in the manner desired and carry out the cutting and joining work with comfort and ease.

General features

The PJ7000 Plate Joiner from Makita has got a Dept of the Cut capability of 25/32 inches.  The tilting angle is 90 degrees. It is equipped with Bearing balls and also boasts a blade cover which is toothless.  There are 6 depth settings. The overall length is 123/32 inches. The total weight of the tool is only 6.5 lbs. while its product dimensions are 7.9 x 19.5 x 10.2 inches. The total package weight is 11.9 lbs. The PJ7000 Plate Joiner from Makita includes a Carrying Case, a Dust bag., a blade and a wrench in its package. The motor utilized in this package is extremely powerful and utilizing a 5.6 Ampere current is able to deliver a very high rotational speed of 11,000 RPM which enables the tool to cut precisely and very quickly in a variety of different kinds of wood regardless of their hardness. In order to make very accurate fence adjustments, there are 3 positive stops at 0°, 45° and 90° for the cast Aluminum pivot fence.  #0, #10, and #20, as well as other common biscuit sizes, are utilized with one-touch stops for the 6 depth settings. The cam locks are easy to operate and are very large. The top handle allows for a very firm grip.

Pros

  • The Plate Joiner is very powerful.
  • It is highly accurate.
  • It comes with all necessary accessories like a carrying case.

Cons

  • It is not the most ergonomic Plate Joiner in the market.

6. XJP03Z 18V LXT Lithium-Ion Cordless Plate Joiner from Makita

The XJP03Z 18V LXT Lithium-Ion Cordless Plate Joiner from Makita has been designed and manufactured to offers a high level of portability as well as excellent performance regardless of where it is being used. It works equally well at the shop and in the field.  It does not even require a cord.  It has the capacity to blend both power and precision and on top of these, it is extremely easy to use and leads to very accurate and strong biscuit joints. It can be used in a variety of different fields such as cabinet construction, furniture making, as well as in other finer woodworking applications. The battery, as well as the charger for the battery, are not included. / These are sold separately.

General Features

The XJP03Z 18V LXT Lithium-Ion Cordless Plate Joiner from Makita has got a high level of improvement in terms of the tool performance in this version. Its battery life is now extended.  The manufacturer is renowned for the creation of Star Protection Computer Controls.  Star Protection is a type of technology in the communication field which allows the tool which is protected by this technology and the battery to engage in a real-time exchange of data and at the same time be able to monitor conditions during its use. The purpose of this technology is to protect against such adverse events as over-discharging, over-loading as well as over-heating. In fact, the tool can be further powered up by the use of Makita 18V LXT and Compact Lithium-Ion batteries which carry the star symbol. It has got a capability of making 320 cuts or 160 joints on a single battery charge. The rack-and-pinion vertical fence system provides highly accurate fence adjustments. There are 3 positive stops for the cast aluminum pivot fence which are at 0, 45, and 90 degrees. The diameter of the blade is 4 inches and the tool has got 6 depth settings enabled with one-touch stops. #0, #10 and #20 biscuit sizes, as well as other sizes, are used. The product dimensions are 8.3 x 16 x 6.8 inches and its weight is 7.4 lbs.

(we have written a guide for choosing the best dual fuel generators).

Pros

  • The Biscuit Joiner can be used anywhere.
  • The Biscuit Joiner can make 320 cuts in one charge.
  • It uses all of the common biscuit sizes.

Cons

  • It is not as powerful as a corded tool.

7. 557 7 Amp Plate Joiner Kit from PORTER-CABLE

The 557 7 Amp Plate Joiner Kit from PORTER-CABLE has the capacity to offer 7 settings for cutting and is able to cut through a variety of different types of wood.  It has been equipped with a very powerful motor which is leading in the industry.  It is extremely powerful and reliable and performs immaculately. Regardless of the profession of the user, the Joiner is equally good for woodworkers and professional cabinet makers. It is extremely versatile and has got an efficient fence design. It boasts a 4-inch blade which is utilized for making standard size cuts.  The tool has been equipped with an extremely innovative fence system with a pivot point that aptly provides highly accurate readings of height.

General Features

The 557 7 Amp Plate Joiner Kit from PORTER-CABLE has got product dimensions of 18 x 13 x 8 inches and it weighs 11.5 lbs. The tool itself is 7 inches high and its weight is 7.5 lbs. It has the capacity to handle many different types of applications and it boasts a strong and powerful 7 Ampere motor which is equipped with a rotating blade. There is an Adjustment knob on the motor which provides a high level of both powers as well as precision.  The motor runs on 120 VAC and rotates the blade at an impressive 10,000 RPM> The tilt of the fence ranges from 0 to 135 degrees for easy placement of both outside and inside corner registrations.  A micro-height adjustment knob along with a positive adjustable stop at 90 degrees are able to accurately position the biscuit aimed at high precision combined with a lot of versatility.The tool has got 2 blade sizes for face-frame biscuits as well as standard ones.  While the 4-inch blade is the standard one, it also accepts2-inch blade forsmaller 1 1/2 inch cuts. This blade is,however, sold separately.

Pros

  • The Biscuit Joiner is very powerful at 10,000 RPM>
  • The Biscuit Joiner has 2 blade settings.
  • The Biscuit Joiner is extremely accurate.

Cons

  • The 2-inch blade is not a part of the package but sold separately.

8. 5 Amp Wood Biscuit Plate Joiner from VonHaus with 4″ Tungsten Carbide Tipped Blade, Suitable for All Wood Types, Adjustable Angle and Dust Bag

The 8.5 Amp Wood Biscuit Plate Joiner from VonHaus with 4″ Tungsten Carbide Tipped Blade, Suitable for All Wood Types, Adjustable Angle and Dust Bag makes very quick cuts which are very accurate as well.  It produces very robust and strong miter joints, butt joints, T-joints, as well as corner/edge to edge joints. The tool provides pre-set depth stops for such common biscuit sizes as 0, 10 and 20 with utmost accuracy without the need to measure. Its adjustable fence lets the user employ the tool to be set on an angle. This provides a lot of extra ease for joining mitered pieces. The package comprises a dust port along with a dust bag and this allows the user to clean up the tool quite easily and it also provides a clear view when the tool is being used. The biscuit joiner has got a highly ergonomic design and the grip handle enhances the ability to grip it strongly.

General Features

The 8.5 Amp Wood Biscuit Plate Joiner from VonHaus with 4″ Tungsten Carbide Tipped Blade, Suitable for All Wood Types, Adjustable Angle and Dust Bag has the capacity to create very strong biscuit dowel connection in order to suit the project of the user as per the application.  The grip on the top is very large and this enables the user to get a very strong grip on the tool. The rest of the body is extremely slim and this facilitates the smooth operation of the equipment. Besides the pre-set stops for the 0, 10, and 20 common biscuit sizes, the tool comes with an ‘M’ setting. This stands for ‘Manual’ and puts the tool in a position to cut custom depths. Once the dust collection bag is connected to the dust port on the Joiner with just a push, a suction function would be enabled during the time that the biscuit joiner is being used. This features greatly facilitates leaping the working area clean and protects from any possible flying debris. This way, the user is able to get a very clear view of the workpiece. The blade diameter is 4 inches and the cutting speed is 10,000 RP<. Thegroove width is 5/32 inches and the amperage is 8.5 Amps. The product dimensions are 16.5” X 13.5” X 6” inches while the weight is just 8.4 lbs.

Pros

  • The tool is very powerful.
  • The tool provides a clear view of the cutting operation.
  • The tool is equally good for all types of wood.

Cons

  • Information on warranty is not available.

9. TruePower Biscuit Plate Joiner from Gino

The 01-0102 TruePower Biscuit Plate Joiner from Gino Development with Carbide Tipped Blade, 4″ has been designed and engineered for very accurate and at the same time very powerful operation to make cuts and form joints at very high rotation speed. The tool is extremely quick and provides very easy biscuit cuts in order to accomplish the task of making extremely sturdy and strong miter joints, butt joints, edge to edge cuts as well as T-joints. The powerful and accurate tool includes an adjustable fence along with a dust port and a dust bag to ensure that the working area remains absolutely clean during operation.  This enables a very clear view of the workpiece by the user and facilitates the user in exercising complete control over the cutting operation.

General Features

The 01-0102 TruePower Biscuit Plate Joiner from Gino Development with Carbide Tipped Blade, 4″ has got present dept stops for common biscuit sizes as the 0, 10 and 20. sizes. Its product dimensions are 19 x 6 x 7 inches and its weight is very low at 8.35 lbs. for the amount of power this unit generates and the facilities it offers. The power rating for this amazingly powerful 01-0102 TruePower Biscuit Plate Joiner from Gino Development with Carbide Tipped Blade, 4″ is 1010 watts which is one of the highest power ratings for this type of tool in the market. This powerful tool is equipped with a robust and high-performance motor that generates a rotational speed of 11,000 RPM at 120 VAC and 60 Hz. The product cannot be ideally used in countries where the electrical current frequency is 50 Hz as it would not be compatible to the mains frequency in such cases. The maximum amount of cutting depth is 0.55 inches which is a very high value and the cutting angle is in the range of 0 to 45 degrees. The tool also includes one 4″ 6T C2 Tungsten Carbide tipped blade in the package besides the main tool.

Pros

  • The tool is extremely powerful.
  • The joiner is extremely quick and accurate.
  • Its cutting depth is very deep.

Cons

  • Fast operation could require frequent dust collection and disposal.

10. 4″ Plate Joiner from Chicago ElectricPower Tools

The 4″ Plate Joiner from Chicago Electric Power Tools is a corded and powerful tool running on 120 VAC to produce a tremendous amount of power and versatility and is designed and engineered to make deep cuts into a variety of different types of wood. It has been provided with an aptly functioning dust collection port and system that allows the debris to be disposed of after the completion of the operation or even during the operation if the operation is being executed at fast speed. The equipment is extremely powerful and is powered by a reliable and strong motor which produces a very high rotational speed to make deep cuts into the workpiece.

General Features

The 4″ Plate Joiner from Chicago Electric Power Tools has the capability to execute dep cuts as deep as 1-1/8 and utilize up to 45 degrees biscuits from such common sizes as the 0, 10 and 20 sizes. It is equipped with an extremely powerful motor with an amperage of 6 amperes which is able to produce a very high rotational speed of 10,000 RPM. The powerful motor and this high rotational speed are responsible for keeping the workpiece stable in the working area and ensure that it would not be unnecessarily moved which could seriously hamper the cutting and joining operation. The fence tilt is adjustable up to 45 degrees. The equipment has been aptly supplied with a dust port and a dust bag which ensure that the debris is moved out to facilitate quick and accurate operation. Moreover, the visibility of the workpiece is facilitated to a greater degree with this dust disposal system.  The pre-set depth stops are available for common biscuit sizes of 0, 10 and 20. The product dimensionsare 20 x 16 x 9 inches and the weight of the product is just 7 lbs.

Pros

  • The equipment is extremely powerful.
  • It is able to make deep cuts.
  • It facilitates dust removal for clear visibility.

Cons

  • Information on warranty is not available.