Best Brad Nailers have a striking plate which hits the head or top of the brad or nail, expelling and driving it into the wood in front of the nailer’s tip.Nailers use various mechanisms to actuate the striker such as an air or gas driven piston, a solenoid, a motor and spring, or an explosive powder charge.
Most nailers are loaded with a magazine of collated nails in coil or strip form. After a nail is ejected and driven, another nail advances into the firing chamber. The process repeats until the magazine is empty or almost empty. This triggers the empty sensing mechanism on the nailers. There is an anti-jamming mechanism to inform if the brads are stuck in the firing chamber.
What are best brad nailers?
These are the smallest members of the nail family. They are thin and wiry thus called wire nails. They have small heads and resemble finishing nails. Brad nails have a rectangular head and are made from an 18-gauge wire. While finishing nail is made of 15 or 16-gauge wire. They can be driven in with a tack hammer or a pneumatic or electric nail gun. A brad gun can vary in length from 5/8th of an inch to 2 1/2 inches.
Where to use brad nails?
These nails are used in cabinets, bookcases, window trimmings, crown mouldings and narrow baseboards. These nails preventdamaging or splitting of the delicate wood and mouldings. Besides as the head is small and barely noticeable it eliminates the need for applyingputtyover the nail holes.
.Best Brad nails are perfect for works where you want to fix wood without using screws or pre-drill. They are also used to hold the material in place while the glue dries, leaving a tiny hole to fill. They are ideal when you want to fix a delicate piece without handling it too much.
When not to use brad nails?
These nails should not be used to fix large crown mouldings and baseboards. They will not be able to carry their weight or hold them in place. For these, you require larger nails such as finishing nails.
Types of best brad nailers
There are two types of brad nailers – pneumatic and electric. They are essential in any toolbox because they are convenient as they speed up the work and offer a cleaner finish.
Pneumatic best Brad Nailers
As the name suggests these nailers work on air pressure. The compressed air is gushed or forced through a lightweight hose. This air rushes through the hose compressing the air pushing the striker that shoots the nail embedding it into place. These are very popular with the users as they produce neat results in a quick and efficient manner. Be it a simple or complex task it is always neat and professional.
One should be cautious while working with pneumatic nailers as the pressurised air can cause accidents. Thus, it is important to handle the tool with care. These nailers come in assorted sizes and shapes consider all the features before you pick yours. The tool consists of a gun, a hose for air to rush through, batteries and cartridge. These may seem like cost-effective options but the maintenance costs such as replacing the hose, oil checks, etc may add up.
Cordless nailers are modified pneumatic nailers that require a rechargeable battery and canisters of compressed air or gas such as nitrogen. The air is released from the canister to drive in the nail. Because of the onboard battery, they may be heavier. Then there are some consumables you may need to refill such as the air canisters.
Electric Brad Nailers
These nailers are powered by an electric motor. This motor powers the gun that drives the nail through embedding it into the material. These are heavier compared to the pneumatic nailer as the motor is housed in the body. Yet these are very efficient tools and work as fast and efficiently as the other option. One should practise the same precautions as the pneumatic nailers and consistently, keep first aid at hand. These may be costlier than the pneumatic nailers but the cost evens out in the long run as these need limited maintenance.
Features to look for on a Best Brad Nailers
The angle of the magazine – The magazine on the best brad nailers is straight instead of angled.
The nail size – a brad nailer is used to drive in 5/8 to 2 inches long nails. Some nailers can only punch in smaller nails between 1 to 1 ¼ -inch nails. So, pick the one that meets your project specifications.
The adjustable – Brad nailers allow you to adjust the depth and power. While others allow you to clear the jam.
- Adjusting the depth – You can finetune the depth in some nailers. On some, you can adjust it manually while others require a special tool.
- Adjusting the power – some nailers come with adjustable power settings. You can choose yours depending on the type and thickness or density of the material you are working with.
- Clearing the jam – brad nailers are designed such that it is easy to clear jammed nails.
The power source – pneumatic best brad nailers can be with or without a hose. You will need an air compressor and hose or compressed gas canisters. Overtime these work out to be costlier than the battery-powered variety. The battery charged ones are heavier and require a little ramp-up time.
The trigger – there are two components to triggers. The first is the first component is the tip or the safety nose of the nailer, that should be pressed against the board to release the fastener. The second component is the trigger that needs to be squeezed to release the nail.
There are contact nailers and sequential nailers.With contact nailers just hold down the trigger and tap the tip of the gun to the object, this releases the fasteners to shoot out the nail. Be cautious while using them as they are activated rapidly. While the sequential nailers release the nail in a sequence. First, the gun needs to be pressed against the board then you pull the trigger to release the nail. These are safer but can be cumbersome.
The guns cylinder should be held perpendicular to the face of the wood or surface to be nailed. This allows the nail to be driven straight into the board. This allows the nail to catch sufficient wood behind the trimming or moulding to remain embedded.
Narrow nose – Due to the narrow gauge the brad nailers have a narrow nose. You shoot a tiny nail from a confined space thus it is necessary you ensure accuracy. The nail gun should have a nose narrow enough to direct the nail into the right spot but wide enough to shoot the nail smoothly without sticking or jamming. This feature helps you distinguish between broad-gauge nailers and brad nailers.
Anti-dry firing mechanism- A nailer with a dry fire lockout feature stops the firing of nails when only a few nails are left in the magazine. The auto lockout mechanism also prevents jamming and reduces the incidents of producing a framing with lesser number of nails.
Top 15 Best Brad Nailers in 2020
|Best Brad Nailers|
|2. Ryobi P320 Airstrike|
|3. DEWALT DC608|
|5. BOSTITCH BTFP12233|
|6. SENCO FinishPro 18MG|
|7.Hitachi NT50AE2 NT50AE2|
|8. WEN 61720|
|9.PowRyte 18 Gauge Air Brad Nailer|
|10. DuRyte Pro 18 Gauge 5/8 to 2-Inch Air Brad Nailer|
|12. 3PLUS HF50SP|
|13. ValuAir SF5040|
|14. AeroPro F50RC|
|15. Stanley TRE650Z|
This nailer comes from the pioneers in power tools. The company has been offering quality tools to carpenters, construction workers, etc. Porter Cable tools ensure high-quality professional results each time.
Design and Build
The highlights of this electric -cordless model are no hose to drag around, no compressor to keep you tied down and no gas. The 100 percent battery power eliminates the need for gas cartridges, hoses and compressors. The motor design ensures a consistent firepower into various materials and climatic conditions. The multiple tool-free setting makes it easy to use. The tool is lightweight with an optimal centre of gravity that prevents fatigue to the user. There are two LED lights – one is for workspace illumination and the other to indicate battery depletion or an error that stalls or jams the tool. There are other features such a tool-free stall release lever and a jam release. There is a depth adjustment window with a wheel that controls the depth of the shot. There are two non-marring rubber tips that protect the delicate surface from damage. There is a safety lock that prevents accidental shots while moving, storing or transporting the gun.
This PORTER-CABLE PCC790LA can punch in around 1300 two-inch brad nails per charge of the 4.0 Ah battery. The brand name is synonymous with finishing and woodwork.
The PCC790LA can drive in 450 nails when loaded with the 1.5 Ah Lithium-ion battery that is included with the pack. This cordless nailer accepts strip fasteners of 18-gauge brads between 5/8 – 2 inches. The magazine loads from the side.
The nailer comes with a PCC680L 20 volts battery and PCC691L charger. The unit comes with a 3-year limited warranty, a 90-day money back guarantee and a 1-year free service contract.
- Electric and cordless
- Rechargeable battery
- Multifunctional LED lights
- Tool free release lever & jam release
- Heavy at 5.1 pounds
- Finding the right brad nail size may be difficult
Ryobi strikes again with this standalone that does not require a hose or a compressor. The best part is that it accepts 1.5 Ah and 4.0 Ah batteries. You can take your pick to ramp up the power.
Design and Build
The Ryobi has two LEDs that turn on with an activation button on the side of the handle, to illuminate the work area. The pleasant surprise is that the lights are activated by depressing the second trigger at the bottom of the handle.
You can select between the contact and sequential actuation. The tool depth of drive adjustment protects the work surface by proper setting of nails. The sequential mode ensures precise placement. You can adjust the air pressure to deliver the fastener to the desired depth. There is an oversized knob at the top of the body instead of the nose, that controls the depth and pressure.There are two non-marring pads to protect the work surface.
The low nail indicator kicks in the dry fire lockout when there are 4-5 nails left in the magazine protecting your work surface. The tool-less jam release is another plus with the nailer. The unit accepts stem pack batteries that may require a little muscle to fit in and pull out.
The Ryobi not only does all the other functions of a brad nailer, but it also has a narrow crown stapler.
The Ryobi can fire up to 700 brads on the 4.0 Ah battery and lesser on the 1.5 Ah. The nailer has a magazine that takes 18-gauge nails of 5/8 t0 2 inches length. The contact actuation delivers 60 nails per minute.
There is a wide belt clip that fits on thick tool belts. The pack includes a pack of 500 1¼-inch brad nailers and an owner’s manual. There are a 90 days exchange and 3-year limited warranty.
- Has twin LED lights
- Battery operated
- Has tool-less jam release
- The short lifespan of the batteries
- The depth driver adjustment should have a dial and point indicator
3. DEWALT DC608
The DeWalt brushless motor controls energy transfer electronically in a manner that allows the tool to deliver 57% more runtime than other brad nailers on the market.
Design and Build
The engine design works the tool in pace with the user ensuring consistent nail penetration into all kinds of surfaces soft and hard. There are two modes of operation – sequential and contact. The sequential mode allows precise placement while the bump or contact mode offers speed.
The contact trip-lock disables the trigger when the tool is idle while the ‘enable’ mode disengages the lock and the tool is trigger-ready. There is an LED that illuminates the work area. The impact resistant top cap protects the nose and the non-marring tip.The cordless feature ensures versatility, manoeuvrability and portability.There is a 12-position dial allows you to choose between applications, depth and power.
The box-style magazine keeps dust and debris out to prevent jams. The straight magazine accepts up to 110, 18-gauge brad nails up to 2 inches. The fastener collation should be by an adhesive. The latch at the nose piece allows for easy jam clearance without the use of tools.
The DeWalt is suitable for people who use nails and brads like construction workers and carpenters. Hobbyists into the woodwork, cobblers who work with leather and woodbeside bookbinders who work with hardbound books covered in leather and thin slices of plywood. They are perfect for installing baseboards, panels, jambs, crowns, shoes, doors, windows, casings and chair rails. A brad nailer is a perfect tool while working with softwood, hardwood and plywood.
The operating pressure of the DeWalt is 70 – 120 PSI. It takes a straight, adhesive-collated magazine of 110 brad nails of gauge-18 and 5/8 – 2 inches length.
The kit includes a cordless battery, a charger, a reversible belt hook, safety glasses and a manual. The unit comes with a 3-year warranty, 90-day moneyback guarantee, and a 2-year service contract on the battery.
- 40% more runtime on the battery
- LED to illuminate the work area
- Two modes of operation – contact and sequential
- The nailer may get noisy
Why we like this product
It is a solid performer with all the features that should be there on a brad nailer. A powerful dependable tool for the house of pioneers in the field at your service.
Matika was founded in 1915 as a motor sales and repair business. It evolved into Matika Corporation in 1958. Over its history, it has been offering products and services to customers. While engaging with them to serve their needs through a parallel development of power tools.
Design and Build
The Makita AF505N has an aluminium body with a cylinder and magazine with an inlet for air at the bottom. The handle has a rubberized soft grip for comfort.It has a durable compact design and weighs only 3 pounds. It is highly manoeuvrable and light on the arms and shoulders of the user. The narrow nose makes it suitable for many finishing jobs.
The tool-less depth adjustment dial is meant to select between a wide variety of applications.
The model has a quick release cam lock that unlocks the nail guide assembly to clear brad nail jams, reducing downtime.
The machine cast nose piece has been engineered for precise contact with the body of the nailer. The nose is covered with a rubber non-marring tip to protect the surface. There is a 360-degree rotatable exhaust port to direct the air away from the user. The tool hook rotates 180 degrees thus the tool remains close at hand but never in the way.
The Makita AF505N drives 5/8 to 2-inch brads into a hard and soft wood. It is perfect for cabinet building, crown moulding and baseboard installations. Floor work, carpet laying and other woodworks.
The Makita’s operating pressure is 60 – 115 PSI at 1.5 SCFM at 90 PSI. It shoots 18-gauge brad nails from a magazine of 100 nails. The brad length is between 5/8 to 2 inches. There is a nail view window to track the number of nails left in the load.
The kit includes accessories like goggles, oil supply (181434-7), a nose adaptor (No-mar tip – HY00000378) and hose connections (311006-A). The model comes with a 3-year warranty.
- a tool-less jam-clearing mechanism
- multidirectional exhaust
- narrow nose
- nail depth adjustment
- customer service could be improved
The BOSTITCH bring you the legacy in fasteners since 1889. This innovative company designs and manufactures fastening tools such as staple guns, nailers, riveters, and glue guns and fasteners such as brads nails, screws, and staples.
Design and Build
This pneumatic nailer functions at 70 – 120 PSI and is compatible with most air compressors. There is a 1/4-inch air fitting that feeds the air hose from the compressor to the tool. It functions at 2.4 SCFM at 60 cycles per minute.
There is no need to compress the contact trip to shoot the brad. The nailer does not require oil, reducing oil stains everywhere. There is a tool-free jam release that eases the task. There is a dial-a-depth feature that controls the countersinking of the nail.
You can choose between sequential and contact operation through the trigger system. The rear exhaust keeps the draft away from the user’s face. The adjustable belt hook fits into the tool belt with ease, there is also a pencil sharpener for your convenience
The smart point technology gives the BOSTITCH an easy reach into narrow areas such as between rafters. It is a versatile tool as the magazine can be loaded with fasteners from 5/8 – 2.5 inches in length.
The BOSTITCH BTFP12233 operating pressure is 70 – 120 PSI. It takes a straight magazine of 100 glue-collated brads, each of 18-gauge up to 2 inches in length.
The BOSTITCH BTFP12233 comes with a carrying case, 3 standard no-mar tips, belt hook, 1/4-inch air fitting, sample fasteners, user’s manual and a 7-year limited warranty.
- Oilless nailer
- Rear exhaust turns away from the user
- Narrow tip to reach small spaces
- Needs a compressor
- Could be standalone with an air/gas canister
Senco builds tools inspired by hard work and designs them such that the work becomes easy. The FinishPro is designed with easy productivity in mind.
Design and Build
This 2 1.8 inches pneumatic brad nailer has a magnesium body giving this ultralight tool durability and manoeuvrability. The easy clear latch eliminates the downtime due to fastener jams. It has a narrow nose to reach a tight corner. The tool weighs 2.48 lbs, it is 9.75 inches in height, 10.5 inches in length and 2.5 inches in width.
This pneumatic tool works at 70 – 120 PSI making it compatible with many air compressors. It has a powerful output of 1.6 SCFM that drives nails through soft and hardwood. This air-powered nailer has a metal cylinder that lasts the lifetime. It houses a stick magazine that holds 110 brads.
It is a pleasure to work with due to its selectable actuation feature. You can fire fast or slow. You can adjust the depth of the drive for the nails to fire deep under the surface or flush with it. If the brads jam just undo the EZ clear latch to clear the cylinder and get back to work. The rear exhaust turns the hot draft away from the user’s face.
The Senco 18MG is good to work with finishes and woodwork such as panels, cabinets, casings, edgings, etc.
The Senco FinishPro operate at the pressure of 70 – 120 PSI or 4.8-8.3 bars. It consumes 1.6SCFM at 60 cycles per minute. The air inlet is quarter of an inch. It uses 18-gauge brad nails 5/8 – 2 1/2 inches range. The power source is an air compressor.
The Senco kit includes wrenches, no-mar pad, plug and a case for the tool. The unit comes with a 5-year limited warranty.
- Thinner body, narrow nose to fire in tight spaces
- Two firing modes – sequential and bump
- Rear exhaust
- Miss setting the nail occasionally
Hitachi leads the research and development of tools to achieve many firsts in the industry. They makeprofessional grade tools for cutting, drilling, concrete, wood and metal works.
Design and Build
The Hitachi comes with dual firing options for precise and continuous driving in of nails. All you need to do is slide the selection control up and down by hand to choose between continuous and intermittent firing. The intermittent mode is ideal for precise driving while the continuous mode is used to drive in nails at a rapid pace using the bumping motion along the work surface.
You can adjust the depth and accuracy of the drive by turning the adjustment dial near the nose of the gun. Turn the knob halfway to make accurate modifications and adjust the depth. Reduce downtime with the high capacity magazine that holds 5/8 – 2-inch nails with a head size range from 0.075-1.9mm. The magazines capacity is 100 nails but can vary depending on the size of the nails. The visual nail indicator helps track the number of nails between reloads.
The ergonomically designed aluminium body is lightweight at 2.2lbs and measures 10 inches in length, 9.18 inches height and 2.37 inches in width. It has a soft Elastomer grip that allows maximum control and extended comfort preventing fatigue during long hours of work. It is equipped with a 360-degree exhaust vent and a no-mar cap to protect the workpiece.
The Hitachi Brad Nailer is an ideal tool for DIY and carpentry projects. It features a high-capacity magazine and an easy depth-of-drive adjustment. This makes it a versatile tool to tackle everything from a cabinet installation, to assembling a picture-frame and door frames to furniture construction and other finishing work.
The Hitachi operates at a pressure of 70 – 120 PSI – this is adjustable to manage the depth and power. It takes in air at the rate of 0.025 cubic feet per cycle at 100 PSI. It has a magazine of 100, 18- gauge adhesive collated nails of 5/8 – 2 inches.
The box contains a pair of safety glasses, a nose-cap mounted on the tool, a protective case for storage and a limited warranty of 5 years.
- Lightweight at 2.2 pounds
- Adjustable depth and power
- Jam clearing
- Can be fed with a 100-nail magazine
- Selective actuation that changes trigger style
- Requires oil
8. WEN 61720
WEN design and distribute high-quality professional tools. Founded in 1951 by Nick Anton this company coalesces tools and electricity to make your life easier and work, highly professional. They make generators, air tools, nailers and other tools to facilitate your work and play life.
Design and Build
This nailer has a 3 pounds die-cast aluminium body prevents fatigue to the user. It has a comfortable, non-slip rubber grip covers an ergonomically designed handle. The WEN is compatible with any compressor with a 1/4-inch NPT inlet fitting that consumes 1.8 CFM of air.
You can choose the direction to release the exhaust using the adjustable port. The spacious box magazine houses 100 nails and keeps them free of debris and dust. The jam clearing quick release latch is in front of the magazine. The magazine has a transparent window or a nail gauge that indicates the number of brads left in the load.
The depth adjustment wheel regulates the distance the nails embed into the material. There is a contact trip that fires only when it is engaged. It is activated when the brad nailer is pressed against the work surface. This ensures maximum safety and minimum misfires.
The WEN 61720 is perfect for light trim work and light assembly of furniture, shoes, leather-bound books crowns etc. It is perfect for delicate work where you want to avoid scarred surfaces and filling putty into the holes.
The WEN drives in 18-gauge brads between 3/4 to 2 inches in length. The magazine capacity is 100 brad nails. The die-cast aluminium body takes an operating pressure of 60 – 100 PSI.
The kit includes a plastic moulded case for storing and carrying the tool. There is a non-detergent oil bottle and S3 and S4 Hex adjustment wrenches. The unit comes with a one-year warranty and customer service supported by skilled technicians.
- an adjustable exhaust port
- quick release magazine
- light aluminium body
- depth adjustment wheel
- contact trip to minimize misfires
- could increase portability with a gas can
PowRyte delivers individual needs of the enthusiasts or professionals. They strive to deliver the most saving at the best value to all the users through their innovative, ingenious, ergonomic designs. They maximize your savings and deliver the best quality tools.
Design and Build
The PowRyte Basic 18 Gauge Air Brad Nailer is lightweight and well-balanced for a fatigue-free job delivery. The ergonomically designed nailer has a rubber grip and a plastic trigger, these features make it slip-free and easy to hold for extended periods of time.
The tool-free jam release mechanism is a latch that allows easy removal of jammed nails. There is a nail reloader that functions as a gauge to keep an eye on the number of nails in the magazine. This feature avoids dry firing. There is a 360-degree swivel port that releases the exhaust away from the user. It also directs the dust and debris away from the project, while keeping it free of oil stains.
The PowRyte Basic is ideal for furniture building, light trimming and finishing jobs. The narrow nose is designed to reach confined places. This nailer is perfect for works that need fixing wood without using screws. It shoots the thinnest nails to hold up the material in place and fix materials that need delicate handling such as crown pieces, mouldings, etc. It delivers brads into leather works such as bookbinding and shoemaking with precise delicacy. It can be used for upholstery work too, where brads are used to hold the material in place while the glue dries.
The PowRyte Basic operates at 70 – 110 PSI powered by a quarter inch air inlet. It fires 18-gauge fasteners of length 3/8 – 2 inches length. The magazine capacity is 100 brad nails this means a long whole between reloads.
The kit contains a pair of Allen wrenches and oil bottle with engine oil and safety glasses and a yearlong warranty.
- Narrow nose to reach narrow places
- Safety glasses and toolkit
- Jam release latch
- Low nail indicator gauge
- Portability could be enhanced with a gas can
DuRyte Pro is a registered trademark of Powell Work Inc. DuRyte is the Right Choice for Durable tools for a lifelong service. They have been manufacturing professional air tools and accessories since 1998.
Design and Build
The DuRyte 18-gauge has a magnesium body with a strong and lightweight design. The compact body design offers a better balance and style. There are a non-slip rubber grip and a plastic trigger for comfort and control.
The detachable no-mar tip prevents the scarring and denting of the work surface. This contractor grade tool has a depth of drive adjustment that allows precise countersinking of nails. The built-in jam release mechanism removes stuck up nails.
There are a dry fire mechanism and a visual nail indicator to prevent empty shots. The unit has a 360-degree adjustable exhaust vent. There is a quarter inch air vent with 18 National Pire thread (NPT).
The ergonomics are in the favour of pneumatic nailers, even when considering the attached hoses. The pneumatic drills weigh up to 3 pounds while the battery and canister powered nailers can weigh up to 7 pounds. The pneumatics fire as soon as you press the trigger this is very satisfying and syncs the user with the machine.
The DuRyte brad nailer is perfect for work on soft and hardwood. This air-powered device is ideal for furniture building, trim work and finishing works.
The DuRyte’s operating pressure is 60-110 PSI. The magazine accepts 100 nails of length between 5/8-inch to 2-inches.
The unit is housed in a blow mould meant for carrying and storing the tool. Besides, there is a pair of Allen wrenches, one oil bottle, a ¼ inch male plug and a two-year warranty.
- Air powered
- A continuous supply of air so no downtime
- Magnesium body lightweight
- Jam release mechanism
- Non-marring tip
- Non-slip rubber grip
- Blow mould case available for carrying and storage
- Could increase manoeuvrability as cordless
- Could be made portable if battery powered
- In case of power outage, you are out of work
Stanley has set standards for excellence since 1843. They delivered innovative powerful tools that are durable and dependable. They are the favourites of DIYers and professionals in the business of repair, building and renovating around the world.
Design and Build
The Stanley is easy to load and drive electric staple and brad nail gun. The unit is 5.9 inches in length, 3 inches in width and 3 inches in thickness. It weighs 2.4 pounds. It has an ergonomically designed plastic and aluminium body that is easy on the hands and arms. The flush nose design gives it easy reach into narrow places.
The Hi/Lo mode adjusts the power of penetration at a switch of a button. The “Lo” mode is perfect for work on softwood and materials while the “Hi” mode makes it suitable for work on hardwood and planks.
It has a simple-to-use design without too many buttons and latches; this also makes it lightweight. For quick jam clearance just restart the machine and you are set.
It drives in heavy duty staples and 1/2, 9/16 and 5/8-inch brad nails into the material. It can be used in packaging, wood and leather works. It is also perfect for stapling carpets into place or repairing fences. It is an easy to use and versatile tool that delivers the staples and brads efficiently.
The Stanley is in its own class as this electric brad nailer accepts 1/2, 9/16 and 5/8-inch brad nails and staplers. This means the magazine has a variable capacity. The 8-foot cord allows you a greater range of the power source. And the nailer is small thus can reach tight spots and places.
It comes with a limited lifetime warranty.
- It is an electric unit thus no extra costs
- Just plug and play
- Versatile as it shoots staples and brads
- Simple ergonomic design
- Well-made trigger
- The 8 feet long cord
- Adjustable power of penetration
- Unjam with ease
- Has a plastic body thus breakable
- Could have replaceable metal part
- As wear could become a dead tool
12. 3PLUS HF50SP
The brand 3Plus deliver quality tools for professionals in the field of pneumatics. The brand sells nailers for different gauge fasteners such as brad nailers, roof nailers, crown staplers and pinners. Look for the signature colours – red and black with a brand label on the side.
Design and Build
The 3PLUS HF50SP has a simple yet efficient design. The tool has every desirable feature built into the nailer. The model uses 3/4 to 2 inches brad nails of 18-gauge. There is a tool-free adjustable depth to control the drive of the nails into the material. The narrow nose not only directs the nail shot into the right place but also makes it easy for nailing in confined spaces.
The two modes of operation are contact and sequential. The contact mode offers speed as it fires the brad at contact. While the sequential mode shoots precise shots into the wood at the desired depth. The body is made of a lightweight composite-plastic magazine that weighs 1/3rdless than the conventional aluminium ones.
There is a quick clear jam release that reduces downtime for the nailer. The magazine keeps the dust and debris out and prevents jams. It accepts straight magazinesof 100 nails. There is an exhaust that turns 360° keeping the air away from the users face during working.
The 3PLUS HF50SP is targeted at trim works, crown fittings, baseboard and carpet installations and different woodworks.
The brad nailer has a magazine with a transparent window. The spring-loaded mechanism pushes the nails into place for the next shot. The magazine has a capacity of 100 nails. The nailer operating pressure of 70 – 120 PSI at 1.5 SCFM at 90 PSI.
The unit comes with a 1/4-inch inlet for the air hose, a pair of Allen wrenches, an oiling bottle and a year’s warranty.
- Pneumatic nailer
- A compressor with regular air supply so no downtime
- Two modes of actuation
- Depth control
- Has the possibility of downtime due to a power outage
13. ValuAir SF5040
The Valu-Air SF5040 is a 2 in one nail and staple gun. It drives in 5/8 to 2 inches brad nails and 1/4th-inch crown staples of 5/8 to 1 5/8 of an inch. It has a high capacity magazine that holds 100 nails per load.
Design and Build
The Valu-Air SF5040 is a precise adjustable depth of drive that does not need any additional tools. The unit comes with a heat treated aluminium hosing this makes it a heavy-duty design that is suitable for all kinds of work environments.
The handle is covered with a comfortable non-slip rubber grip. The tip is covered with a rubber non-marring tip thus no dents or scars on the work surface. The nose is easy to clean in case of a jam – just lift the latch. The exhaust rotates a full 360 degrees thus you can direct the exhaust away from your face.
The ValuAir is a versatile tool as it drives 18-gauge brad nails of lengths between 5/8 to 2 inches and staple crowns of 1/4 inch and crown staples between 5/8 to 1 5/8 inches. It takes a straight magazine of 100 glue-collated brads and staples. The range makes it a tool of choice for a wide range of applications such as packaging and works on soft and hardwood.
The ValuAir operates at 60 – 120 PSI. The air rushes in from the compressor at from a 1/4-inch NPT air inlet fitting. The model consumes 1.6 SCFM of air at 60 cycles per minute.
The kit comes with a one-year warranty, a moulded plastic carrying case, a set of Allen wrenches, an owner’s manual, a set of 100 2-inch brad nails and a set of 100 1 5/8-inch crown staples.
- A versatile tool that shoots brads and staples
- Has a wider range of application
- Depth adjustment
- Heat treated aluminium hosing makes it heavy duty
- Can be made with a dual mode that works with air canisters
14. AeroPro F50RC
This nailer comes from Benner Nawman or BN Products. AeroPro-USA is a well-known brand among professionals who use frame nailers, roofing nailers, connector nailers, palm nailers and floor cleat nailers.
Design and Build
The AeroPro F50RC has a light and strong aluminium body that makes it highly manoeuvrable. It is just under 3 pounds thus easy on the arms and shoulders of the user. As it is a die-cast body there are no joints increasing the longevity of the nailer. The front of the unit takes the magazine the top of this column has a latch release that clears the jams. While the bottom unclips the magazine from the gun for a refill. There is an indicator window that informs on the number of nails left in the load. The back of the nailer has an adjustable knob for sequential and contact firing. There is a depth-of-drive adjustment near the trigger for the exact setting of nails into the material. There is a multi-directional exhaust that directs the air away from the operator and work surface. There is a specially hardened one-piece drive blade for professional applications and a Teflon O-ring that protects the piston from wearing.
This is a useful tool with a wide range of use. It can be used to fix fences, make and mend cabinets and other furniture. It can be used to finish window trimmings, door casings, mouldings and boards. Using these nailers prevents damaging or splitting delicate wood and mouldings.
This unit functions at 70 – 110 PSI of air pressure delivered at the rate of 1.5 SCFM at 90 PSI. It accepts 5/8 to 2 inches 18-gauge brad nails that fit as a collated magazine into the nailer.
The tool comes with a 1-year limited warranty.
- Teflon O-ring to protect the piston
- One-piece drive blade
- Adjustable depth drive
- Contact and sequential modes
- Could be made versatile by making it a cordless run on battery or air canister
15. Stanley TRE650Z
Stanley has been synonymous with innovation, quality and value since last 170 years. Their tools are used by do-it-yourselfers mending a fence or a contractor building a house.
Design and Build
The Stanley TRE650Z is 12 inches in length, 11.5 inches in height and 3.5 inches in width and weight around 4.5 pounds. This electric brad nailer has a comfortable ergonomic design to reduce hand fatigue. Its handle is covered with a soft rubber grip. The easy to load magazine has a side loading design with a jam clearing mechanism that saves times and prevents frustration. There is a brad indicator to tell when the magazine is empty. To ensure the best performance, use the TRE650 on a dedicated electrical circuit. It is recommended for use without a power strip, or other power distributing or dividing devices.
There is a Hi/Lo power dial. The hi mode is a depth adjustment that shoots the brad deeper than the Lo mode. The Hi mode is perfect for working on hardwood and Lo mode for softwood and delicate materials like mouldings, etc. This brad nailer is versatile and can be used for carpet fitting over floors and staircases. It can be used to fit floorboards and mouldings, etc. As this is an electric model it is safe to use by learners of carpentry, design and shoemaking too.
The Stanley uses 5/8 to 2-inch brad nails thus the magazine has a variable capacity. It has an 8-foot cord that allows you a greater movement away from the power source. The nailer is small and light this can reach small tight places with ease.
The TRE650Z comes with a stand, a carrying case and a lifetime limited warranty.
- Hi/Lo mode makes it versatile
- Long cord for wider reach
- Easy to load and release a jam
- An easy plug and play design
- Environmentally friendly as it uses only electricity
- A useless tool in the absence of power